ES Windows Roofing Nationwide

ES Windows Roofing: The Sherman Oaks Owner’s Guide

ES Windows roofing systems installed in Sherman Oaks homes typically run $8,000-$20,000 for full replacement and $400-$1,800 for targeted repairs, with most ES Windows-compatible flashing, membrane, and seal components available same-day through our local supply chain. We stock the critical wear parts that fail first on ES Windows installations in the San Fernando Valley’s heat-cycling climate. Most Sherman Oaks owners discover the problem after the first hard rain of the season, when water shows up at the window-to-roof junction that ES Windows integrates into its system.

Call (213) 221-0788

Which ES Windows Models This Applies To

ES Windows produces impact-rated and standard window systems with integrated roof flashing kits, primarily the ES-7000 impact series, ES-5000 architectural line, and the older ES-3000 builder-grade units still common in Sherman Oaks homes built between 2008 and 2016. The critical compatibility point is the flashing profile depth: ES-7000 series uses a 2.5-inch integrated pan flashing, while the ES-5000 and ES-3000 lines use a 1.75-inch standard pan. We see mismatched aftermarket flashing cause leaks within 18 months because the shallower pan cannot handle the water volume the wider ES-7000 sill collects during a Valley downpour.

To identify your series, check the etched code in the glass corner (format: ES-XXXX-YY) or the aluminum spacer bar label visible when you open the sash. If the label is worn, measure the exterior sill depth from the glass to the outer edge: 2.5 inches confirms ES-7000, 1.75 inches indicates ES-5000 or ES-3000. We source OEM ES Windows flashing and membrane from the Florida distribution center, though we also stock compatible aftermarket pans from MFM Building Products that meet the same Miami-Dade impact standards at roughly 60 percent of OEM cost. The aftermarket option carries our standard warranty; the OEM carries both our warranty and ES Windows’ material defect coverage. We document which you chose on the written quote before work starts.

Signs Your ES Windows Roofing Is Failing

• Water staining on interior drywall below or beside the window unit. This indicates the primary flashing pan has separated from the window frame or the membrane has cracked at the corner joints. In Sherman Oaks, the daily 30-degree temperature swing between August afternoons and desert-cooled nights fatigues the butyl tape seal faster than coastal installations.
• Visible gaps between the window frame and the roofing material. The ES Windows nailing fin relies on a continuous sealant bed; when this shrinks or the installer originally used non-UV-stable caulk, the gap opens to direct water intrusion. We find this most often on south-facing elevations where UV exposure peaks.
• Peeling paint or efflorescence on exterior stucco below the window. This is delayed evidence: water has been entering the wall cavity, traveling down the weather-resistive barrier, and exiting at the first obstruction. By this stage, the OSB or plywood sheathing may be compromised.
• Window operation becomes stiff or the sash binds. The ES Windows frame is designed to stay square within a specific installation tolerance; when the flashing fails and the sill plate absorbs moisture, the frame racks slightly. The binding you feel is the sash meeting the jamb at an angle it was not built for.
• Musty odor near the window that intensifies after rain. This signals active mold growth in the wall cavity, which in Sherman Oaks’ dry climate almost always means a concentrated leak point rather than general humidity. The ES Windows integrated design means the leak is almost certainly at the roof-to-window transition, not the glass seal.

Before

After

Replacement Cost & What’s Included

For ES Windows roofing component replacement in Sherman Oaks, our installed pricing breaks down as follows:

• ES-3000/ES-5000 flashing pan replacement: $400-$900 (parts $120-$280, labor and membrane $280-$620)
• ES-7000 deep-pan flashing replacement: $650-$1,400 (parts $200-$450, labor and membrane $450-$950)
• Full window-to-roof membrane replacement with new flashing: $1,200-$1,800
• Sheathing repair where water damage extends behind the flange: add $300-$600 per linear foot of affected wall

The range reflects three variables: the ES series (deeper pans require more labor), the extent of hidden water damage we find after removing the old flashing, and whether the original installation used the ES Windows prescribed two-layer membrane or a single-layer shortcut. We inspect with a thermal imager before quoting and include the photo record in your documentation. Under Clause 1 of The Haven Standard, the price we write is the price you pay; if we find additional damage, we stop, photograph it, and present a signed change order before proceeding. No exceptions since 2007.

DIY or Call Us?

An owner can safely check three things: confirm the series code from the glass etch, look for visible gaps in daylight from the exterior, and run a hose at low pressure across the roof-to-window junction for five minutes while someone watches inside. What you cannot safely do is remove the flashing pan itself. The ES Windows system requires temporary support of the window frame while the pan is extracted; without it, the frame drops, the glass stresses, and you are buying a window unit, not a flashing. The membrane beneath is also load-bearing in ES’s design, not merely waterproofing. We carry the frame jacks and the correct membrane rolls on every truck. If your inspection suggests failure, call (213) 221-0788 and we will schedule a free estimate with thermal imaging included.

FAQs