ES Windows Kitchen Remodeling Nationwide

ES Windows Kitchen Remodeling: The Sherman Oaks Owner’s Guide

ES Windows kitchen remodeling in Sherman Oaks typically runs $14,000-$45,000 installed, depending on whether you’re refreshing fixtures or reconfiguring the layout with new cabinetry, countertops, and integrated window systems. We stock ES Windows-compatible framing, flashing, and seal kits for their 5000, 6000, and 8000 series, and we can usually schedule a site visit within 24-48 hours to measure and spec the integration. Most Sherman Oaks homeowners discover their ES Windows kitchen setup needs attention when they notice drafts around the frame, condensation between panes, or the sash not seating flush after years of thermal cycling in the Valley heat.

Call (213) 221-0788

Which ES Windows Models This Applies To

ES Windows produces three aluminum series relevant to kitchen installations: the 5000 (single-hung and fixed), 6000 (horizontal roller and casement), and 8000 (impact-rated for high-velocity zones). The critical compatibility point is the frame depth, 2⅜ inches on the 5000/6000 and 3¼ inches on the 8000, which determines whether your kitchen countertop backsplash or cabinet return will clear the sash hardware. Check the etched mark in the glass corner or the stamped label on the frame head for the series prefix, ES-5, ES-6, or ES-8.

We source OEM ES Windows parts directly through their Florida distribution center, but for hardware and weatherstripping we often install Truth or Amesbury equivalents that meet the same AAMA 2605 finish spec and carry comparable warranties. The aftermarket route saves roughly 15-20% on hardware costs without compromising the thermal break integrity, which matters in Sherman Oaks where summer surface temperatures on south-facing kitchen windows regularly hit 140°F. One gotcha: the 6000 series casement uses a proprietary hinge bracket spacing, 4½ inches on center, that aftermarket suppliers sometimes mislabel as standard 4-inch. We verify every bracket against the removed part before ordering.

Signs Your ES Windows Kitchen Remodeling Is Failing

• Draft around the frame even when closed. The compression seal has hardened or the frame has shifted slightly in the opening, common in Sherman Oaks homes built on the expansive clay soils near the Santa Monica Mountains. The gap lets conditioned air escape and drives up your PG&E bill.
• Fog or moisture between glass panes. The insulated glass unit (IGU) seal has failed, releasing the argon fill and destroying the thermal barrier. In kitchen installations above sinks or ranges, steam accelerates this failure by 30-40% compared to dry rooms.
• Sash sticks, binds, or won’t stay open. The balance system, either a coil spring or block-and-tackle, has worn out or corroded from grease and moisture in the kitchen environment. ES Windows 5000 series single-hung units are particularly prone if the tilt latch gets forced.
• Water staining on the drywall below the window. The sill pan or end dam flashing was omitted or improperly sealed during original installation, a code requirement in California since the 2007 CBC update. Water follows the sub-sill and rots the cabinet top or framing below.
• Frame corners gap or separate. The mechanical fasteners in the aluminum extrusion have backed out or the thermal break adhesive has degraded. This is structural, not cosmetic, and the sash will eventually drop out of square.

Before

After

Replacement Cost & What’s Included

The $14,000-$45,000 kitchen remodel range covers everything from a cabinet-and-counter refresh with one or two window swaps to a full gut with structural modifications, custom KraftMaid or Wellborn cabinetry, Cambria or Silestone countertops, and multiple ES Windows openings reconfigured for flow and light. What drives the spread: whether we keep the existing footprint (lower) or move plumbing, gas, and electrical (higher); whether the ES Windows are standard or impact-rated 8000 series; and whether the finishes are builder-grade or full custom.

Every quote is flat-priced with a written scope before work starts, per Clause 1 of The Haven Standard. No change proceeds without a signed change order. The 365-Day Done Right Promise covers all labor, and ES Windows OEM glass carries a 20-year manufacturer’s warranty against seal failure. We pull permits through the City of Los Angeles and pass inspection before we call the job complete.

DIY or Call Us?

There’s a safe middle ground for ES Windows owners. You can verify the series from the etched glass mark, check the sash operation for binding points, and photograph any water staining for our review. What you should not attempt: removing a fixed or impact-rated sash without proper support, cutting into the integrated flange on a nail-fin installation, or disturbing the thermal break during hardware replacement. The 8000 series impact glass weighs 8-12 pounds per square foot, a two-person lift minimum, and improper handling voids the Miami-Dade rating.

We’ve seen DIY attempts in Sherman Oaks where the homeowner cracked the IGU trying to force a stuck sash, turning a $350 balance repair into a full $1,800 window replacement. Measure twice, write it down, then build it. If you’re unsure which series you have or whether the flashing is the problem, call (213) 221-0788 and we’ll schedule a free estimate with a documented photo record of what we find.

FAQs