Jerith Roofing Nationwide

Jerith Roofing: The Sherman Oaks Owner’s Guide

Jerith aluminum roofing components in Sherman Oaks typically run $400-$1,800 to repair and $8,000-$20,000 for full replacement, with most Jerith-compatible flashing, fasteners, and panel sections stocked on our trucks for same-day installation. We carry the 6-inch K-style and 7-inch half-round profiles Jerith used across its Southwest series, plus the stainless-steel clip systems that fail first in our local climate. Most Sherman Oaks owners discover the problem after the first hard rain of November, when water tracks behind a loosened standing-seam clip or a thermal-split panel lets daylight through the attic sheathing.

Call (213) 221-0788

Which Jerith Models This Applies To

Jerith produced three aluminum roofing lines relevant to Southern California: the Southwest Series (1988-2004), the Designer Series (2001-2012), and the limited-run Coastal Series (2005-2009). The Southwest Series used a proprietary 1-inch snap-lock standing seam with 16-inch panel width; the Designer Series switched to a 1.5-inch mechanical lock and 12-inch width. The clip spacing differs between the two, 24 inches on-center versus 18 inches, and mixing clips between series is the most common compatibility error we see on Sherman Oaks inspections.

To identify your series, check the underside of any lifted panel for a stamped four-digit date code and series abbreviation, SW or DS. If the stamp is painted over, measure the seam height with a ruler from the flat of the panel to the top of the rib. The Coastal Series used a hidden-fastener system with marine-grade 316 stainless clips, but Jerith sourced these clips from two different vendors; the later vendor’s clips are slightly thicker and will bind in the earlier track. We stock both clip geometries and will match what is on your roof, not guess.

On the OEM-versus-aftermarket question: Jerith discontinued roofing manufacturing in 2012 and sold remaining inventory through 2015. True OEM panels are now scarce in Southern California, and we do not promise them. Our aftermarket panels are .032-inch 3105-H14 aluminum, matching Jerith’s alloy spec, with a Kynar 500 finish in the standard Southwest color palette. For historic consistency in neighborhoods like the hills south of Ventura Boulevard, we can source custom-run panels to match faded originals, though lead time extends to three weeks and the price moves accordingly.

Signs Your Jerith Roofing Is Failing

• White oxidation streaking on panel flats. This is filiform corrosion starting at cut edges or scratches in the Kynar coating, accelerated by the Santa Ana winds carrying salt and particulate from the coast. Once the streaking spreads beyond 6 inches from any edge, the aluminum substrate is thinning and the panel will pinhole within two to three rainy seasons.
• Clicking or pinging during morning warming. Jerith’s aluminum expands roughly twice as much as steel per degree, and clips that were over-torqued at install or have worked loose will let the panel foot shift in the bracket. The noise is the panel sliding against a clip that no longer holds it down; left alone, the slot elongates and the panel lifts in wind.
• Water staining at rake edges or valleys. Jerith used a foam closure strip at panel ends that degrades in UV after 12-15 years in Sherman Oaks sun. When the foam collapses, wind-driven rain enters the rib cavity and travels downhill until it finds a joint or fastener hole. The stain location is rarely the leak origin; we trace the rib path with a hose test to find the actual entry.
• Panel oil-canning between seams. This waviness indicates the panel was over-fastened or the substrate deck has deflected, leaving the aluminum with no room to expand. It is primarily an aesthetic issue until the stress concentrates at a seam and cracks the mechanical lock; at that point water intrusion follows within the next storm cycle.
• Fastener heads backed out or missing. Jerith’s original fasteners were zinc-plated steel with an EPDM washer. The zinc plating lasts 10-14 years in our dry climate, after which the steel head rusts, expands, and pushes the washer off the shank. A fastener without compression lets the panel lift in wind, and the elongated hole becomes a new leak path.

Before

After

Replacement Cost & What’s Included

What drives the range: access difficulty (steep pitches above 6:12 common in the Sherman Oaks hills add labor hours), whether the original clips are reusable (Coastal Series clips often are not), and how many panels need matching versus full replacement. Under Clause 1 of the Haven Standard, we deliver a written line-item quote before any work starts; the price you sign is the price you pay, with change orders required and signed for any deviation. Our 365-Day Done Right Promise covers the installation and materials. Every visit includes a documented photo record of deck condition, clip torque readings, and finished seams, uploaded to your project folder before we leave.

DIY or Call Us?

There is one safe homeowner check: from the ground or a secure ladder at gutter height, look for the symptoms above and note their locations. Do not walk an aluminum roof. The panels dent under foot traffic, the seams are slick when dew-covered, and a 6:12 pitch on a two-story Sherman Oaks home is a serious fall hazard. We have replaced panels that were damaged by a homeowner’s well-intentioned inspection and then leaked worse than the original problem.

What goes wrong with DIY repair: the snap-lock seam requires a hand seamer and a specific crimp sequence to re-engage; done wrong, the panel looks seated but lifts in the first Santa Ana. The mechanical-lock seam needs a powered seamer with throat depth matched to the seam height. We have also seen homeowners use standard galvanized fasteners from a hardware store; the dissimilar metal accelerates galvanic corrosion of the aluminum panel, and the wrong washer profile does not seal the rib cavity. If you are weighing the repair yourself, call us at (213) 221-0788 for a free estimate first. The written quote costs nothing and gives you a benchmark for any DIY material list.

FAQs