KraftMaid Kitchen Remodeling Nationwide

KraftMaid Kitchen Remodeling: The Sherman Oaks Owner’s Guide

We stock and install KraftMaid-compatible kitchen remodeling components in Sherman Oaks, with typical installed projects running $14,000-$45,000 depending on scope, layout changes, and finish selections. Most cabinet-only refreshes with KraftMaid semi-custom lines fall in the $4,000-$13,000 range for installation, while full kitchen tear-outs with layout reconfiguration push toward the upper band. We carry current KraftMaid door styles, drawer box assemblies, and hardware in our Van Nuys warehouse, and we can typically pull stock for measurement within 48 hours of your call.

Call (213) 221-0788

Most Sherman Oaks homeowners realize their KraftMaid kitchen is failing when drawer boxes start dropping out of square, or when the soft-close hinges lose their dampening and cabinets start slamming shut. In the older homes off Ventura Boulevard, we also see water-damaged sink bases where the particleboard core has swelled past recovery, and corner lazy Susans that no longer rotate smoothly because the polymer shelf supports have fatigued.

Which KraftMaid Models This Applies To

KraftMaid organizes its cabinetry into three main tiers: Vantage (entry stock), Canvas (semi-custom with more door styles and sizing), and Impresa (full custom with made-to-order dimensions). The parts and installation methods differ materially between them. Vantage uses a ½-inch plywood box with standard 3-inch increment sizing; Canvas moves to ¾-inch plywood with ⅛-inch incremental adjustments available; Impresa is engineered to your exact field measurements with no modular constraints.

To identify your series, check the interior stamp on the hinge side of any wall cabinet, or the KraftMaid spec label affixed to the back of drawer boxes from the 2018 production run forward. The four-digit model prefix tells us everything: VNT for Vantage, CVS for Canvas, IMP for Impresa. If your cabinets predate 2015, you may have the discontinued “Montclair” or “Sonoma” lines, which used a different hinge boring pattern. We keep adapter plates in stock for these legacy mounts, but the door itself must be matched by overlay measurement. OEM KraftMaid doors run 15-20% more than quality aftermarket equivalents from Barker or Cabinet Door World, but the color match to existing boxes is exact. Aftermarket works fine for full replacements; OEM matters when you’re blending new doors into a partially original kitchen.

One compatibility gotcha we see regularly in Sherman Oaks: the Canvas soft-close undermount drawer slide (Blum Tandem plus KraftMaid bracket) has a 21-inch and 22-inch version that look identical until you measure the rear bracket hole spacing. The wrong slide will mount but bind within two weeks of use.

Signs Your KraftMaid Kitchen Remodeling Is Failing

• Drawer fronts pulling away from the box. The MDF front panel is joined to the solid wood drawer box with confirmat screws and a locking dado. In Sherman Oaks, the low-humidity Santa Ana season causes seasonal contraction that loosens this joint. We see this most in south-facing kitchens where temperature swings are widest.
• Doors no longer self-closing or slamming shut. The Blumotion hinge cup integrates a polymer damper that degrades after roughly 80,000 cycles, or about 7 years of daily use. The hinge itself is fine; the damper is a replaceable insert, but most homeowners don’t know to ask for it separately.
• Sink base cabinet floor bubbling or softening. KraftMaid uses a vinyl-wrapped particleboard floor in standard sink bases, not the plywood upgrade. Even a slow drip from a P-trap union will wick through the seam tape and swell the core. By the time you see the bubble, the structural integrity is gone.
• Corner cabinet hardware grinding or catching. The LeMans or kidney-shaped lazy Susan systems use a polymer bearing race that collects grit and grease. In homes near the 405 where construction dust is constant, this accelerates wear. The bearing is replaceable, but the shelf itself often warps from uneven loading.
• Adjustable shelf pins pulling out of their holes. The 5mm metal pin is stronger than the MDF sidewall in Vantage series boxes. Overloading with cast-iron cookware causes the hole to elongate. Once the hole is blown out, the only permanent fix is a hardwood dowel and re-drill, not a larger pin.

Before

After

Replacement Cost & What’s Included

Our Sherman Oaks kitchen remodeling pricing follows the ranges below. Every quote is a flat written price with line-item scope before any work starts, under Clause 1 of the Haven Standard.

What drives the range: layout changes requiring electrical or plumbing relocation add $800-$2,400 per trade; wall removal with structural header installation runs $3,500-$8,000 depending on span and load; flooring replacement under cabinets versus around them changes labor by 30-40%. Our quotes include permit pulling, inspection scheduling, and the documented photo record delivered at project close. The 365-Day Done Right Promise covers all workmanship; manufacturer warranties on KraftMaid products run limited lifetime on drawer boxes and hinges.

We also stock and install parts for Cambria and Silestone countertops, plus Kohler fixtures, for homeowners doing partial refreshes rather than full remodels.

DIY or Call Us?

There’s a clear line between what a homeowner can safely assess and where professional installation becomes necessary. You can check: whether a drawer slide is fully seated in its rear bracket, whether a hinge screw has backed out, or whether shelf pins are simply misplaced rather than the hole stripped. A Phillips head and ten minutes will answer those questions.

Where DIY goes wrong: adjusting a corner cabinet’s LeMans hardware requires setting the arm geometry to within ⅛ inch or the shelf will collide with the door frame. Replacing a sink base floor involves supporting the countertop across a 36-inch span while the wet carcass is removed, and any plumbing disconnect without a proper shut-off risks flooding. We don’t recommend homeowners attempt structural modifications, electrical relocations, or gas line adjustments for range or cooktop moves. Our crews are background-checked and uniformed; every visit includes the photo record as standard.

Call (213) 221-0788 to schedule your free estimate. We’ll measure twice, write it down, then build it.

FAQs